Skip to main content
NetApp Knowledge Base

Error when upgrade Reference Configuration File (RCF)

  1. Last updated
  2. Save as PDF
Views:
217
Visibility:
Public
Votes:
1
Category:
factory-configured-cluster
Specialty:
core
Last Updated:

Applies to

  • Cisco Nexus cluster and storage network switches
  • Reference Configuration File (RCF)

Issue

Display ^ error when upgrade RCF file.

40gj3-rtp-1(config)# #********** Intra-Cluster ISL ports **********
40gj3-rtp-1(config)#
40gj3-rtp-1(config)# interface Ethernet1/31
40gj3-rtp-1(config-if)#  description Intra-Cluster Switch ISL Port 1/31 (port channel)
40gj3-rtp-1(config-if)#  priority-flow-control mode auto
                                              ^
% Invalid command at '^' marker.
40gj3-rtp-1(config-if)#  switchport mode trunk
                                   ^
% Invalid command at '^' marker.
40gj3-rtp-1(config-if)#  switchport trunk allowed vlan 1
                                   ^
% Invalid command at '^' marker.
40gj3-rtp-1(config-if)#  mtu 9216
                          ^
% Invalid command at '^' marker.
40gj3-rtp-1(config-if)#  channel-group 1 mode active
40gj3-rtp-1(config-if)#  no shutdown
40gj3-rtp-1(config-if)#
40gj3-rtp-1(config-if)# interface Ethernet1/32
40gj3-rtp-1(config-if)#  description Intra-Cluster Switch ISL Port 1/32 (port channel)
40gj3-rtp-1(config-if)#  priority-flow-control mode auto
                                              ^
% Invalid command at '^' marker.
40gj3-rtp-1(config-if)#  switchport mode trunk
                                   ^
% Invalid command at '^' marker.
40gj3-rtp-1(config-if)#  switchport trunk allowed vlan 1
                                   ^
% Invalid command at '^' marker.
40gj3-rtp-1(config-if)#  mtu 9216
                          ^
% Invalid command at '^' marker.
40gj3-rtp-1(config-if)#  channel-group 1 mode active
40gj3-rtp-1(config-if)#  no shutdown
40gj3-rtp-1(config-if)#
40gj3-rtp-1(config-if)# interface port-channel1
40gj3-rtp-1(config-if)#  service-policy input ROCE_QOS
Unable to perform the action due to incompatibility:  Module 1 returned status "TCAM region is not configured. Please configure TCAM region and retry the command"

40gj3-rtp-1(config-if)#  priority-flow-control mode auto
40gj3-rtp-1(config-if)#  switchport mode trunk
40gj3-rtp-1(config-if)#  switchport trunk allowed vlan 1
40gj3-rtp-1(config-if)#  mtu 9216
40gj3-rtp-1(config-if)#  no shutdown
40gj3-rtp-1(config-if)#
40gj3-rtp-1(config-if)# end

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.