Skip to main content
NetApp Knowledge Base

SRM reprotect fails with error "Cannot protect virtual machine"

Views:
75
Visibility:
Public
Votes:
0
Category:
ontap-storage-replication-adapter
Specialty:
virt
Last Updated:

Applies to

  • NetApp Storage Replication Adapter (SRA)
  • VMware Site Recovery Manager (SRM)

Issue

SRM reprotct fails with following error. However, its get successful if try reprotect after sometime.

vmware-dr.log:

 -->       "          <msg>The operation was only partially completed for the protection group &apos;Test_VM_Netapp&apos; since a protected VM belonging to it was not successful in completing the operation. Cannot protect virtual machine &apos;VM_Name&apos; because its config file &apos;[snap-DataStore_Name] VM_Name/VM_Name.vmx&apos; is located on a non-replicated or non-protected datastore.</msg>",
-->       "</fault>",
-->       "      <Children>",
-->       "        <Step elapsedTime="00:00:00" endTime="2023-01-09T07:35:21Z" objectId="vm-protection-group-xxxx" startTime="2023-01-09T07:35:21Z" status="error">",
-->       "          <Key>RecoveryStepProtectionGroup.name</Key>",
-->       "          <Name>Protection Group ProtectionGroup_Name</Name>",
-->       "          <fault>",
-->       "              <_type>dr.fault.MultipleFault</_type>",
-->       "              <faults>",
-->       "                  <_length>2</_length>",
-->       "                  <_type>vmodl.MethodFault[]</_type>",
-->       "                  <e id="0">",
-->       "                      <_type>dr.storageProvider.fault.ConfigFileNotReplicated</_type>",
-->       "                      <configFile>[snap-DataStore_Name] VM_Name/VM_Name.vmx</configFile>",
-->       "                      <msg/>",
-->       "                      <vm>",
-->       "                          <_type>vim.VirtualMachine</_type>",
-->       "                          <moid>vm-xxxx</moid>",
-->       "                          <serverGuid>xxx-xxxx-xxxx-xxxx-xxxx</serverGuid>",
-->       "      </vm>",
-->       "                      <vmName>VM_Name</vmName>",
-->       "    </e>",
-->       "                  <e id="1">",
-->       "                      <_type>dr.replication.fault.IncompleteOperation</_type>",
-->       "                      <msg/>",
-->       "                      <protectionGroup>",
-->       "                          <_type>dr.replication.VmProtectionGroup</_type>",
-->       "                          <moid>vm-protection-group-xxxx</moid>",
-->       "                          <serverGuid>xxx-xxxx-xxxx-xxxx-xxxx</serverGuid>",
-->       "      </protectionGroup>",
-->       "                      <protectionGroupName>ProtectionGroup_Name</protectionGroupName>",
-->       "    </e>",
-->       "  </faults>",
-->       "              <msg>Cannot protect virtual machine &apos;VM_Name&apos; because its config file &apos;[snap-DataStore_Name] VM_Name/VM_Name.vmx&apos; is located on a non-replicated or non-protected datastore. The operation was only partially completed for the protection group &apos;ProtectionGroup_Name&apos; since a protected VM belonging to it was not successful in completing the operation.</msg>",
-->       "</fault>",

 

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.