Report sas.adapter.firmware.fault on EMS

Last updated
Save as PDF
Share
1. Share
2. Tweet
3. Share

Views:: 81

Visibility:: Public

Votes:: 0

Category:: ontap-9

Specialty:: HW

Last Updated:

Applies to

ONTAP 9

Issue

Receive the following alerts in EMS log

[?]  Sun Dec 10 01:29:12 +0900 [node2: pmcsas_timeout_0: sas.adapter.firmware.fault:notice]: Detected firmware fault 0xffffffff on SAS adapter 0a.

[?]  Sun Dec 10 01:29:14 +0900 [node2: pmcsas_asyncd_0: sas.adapter.reset:debug]: Resetting SAS adapter 0a.

[?]  Sun Dec 10 01:29:19 +0900 [node2: pmcsas_asyncd_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'Start kicking open SDM batch window'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PHY UP [4] RATE 0x8 PS 0x1, NPIP 1 :: DEVTYPE 0x20, TGT 0x2, INIT 0x2, ADDR 500a09800e2fe8bf'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PORT UP -- 0b'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PHY UP [5] RATE 0x8 PS 0x1, NPIP 2 :: DEVTYPE 0x20, TGT 0x2, INIT 0x2, ADDR 500a09800e2fe8bf'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PHY UP [6] RATE 0x8 PS 0x1, NPIP 3 :: DEVTYPE 0x20, TGT 0x2, INIT 0x2, ADDR 500a09800e2fe8bf'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PHY UP [7] RATE 0x8 PS 0x1, NPIP 4 :: DEVTYPE 0x20, TGT 0x2, INIT 0x2, ADDR 500a09800e2fe8bf'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PHY UP [0] RATE 0x8 PS 0x1, NPIP 1 :: DEVTYPE 0x20, TGT 0x2, INIT 0x2, ADDR 500a09800851dd0d'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PORT UP -- 0a'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PHY UP [1] RATE 0x8 PS 0x1, NPIP 2 :: DEVTYPE 0x20, TGT 0x2, INIT 0x2, ADDR 500a09800851dd0d'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PHY UP [2] RATE 0x8 PS 0x1, NPIP 3 :: DEVTYPE 0x20, TGT 0x2, INIT 0x2, ADDR 500a09800851dd0d'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_admin_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'PHY UP [3] RATE 0x8 PS 0x1, NPIP 4 :: DEVTYPE 0x20, TGT 0x2, INIT 0x2, ADDR 500a09800851dd0d'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_asyncd_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'Port 0: disabled 0, up 4, down 0: old state 3 --> new state 3'}

[?]  Sun Dec 10 01:29:21 +0900 [node2: pmcsas_asyncd_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'Port 1: disabled 0, up 4, down 0: old state 3 --> new state 3'}

[?]  Sun Dec 10 01:29:25 +0900 [node2: pmcsas_asyncd_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'Transition Comparing this: [IOM1] and next: [IOM1] ...'}

[?]  Sun Dec 10 01:29:25 +0900 [node2: pmcsas_asyncd_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'Asyncd device scan done.'}

[?]  Sun Dec 10 01:29:25 +0900 [node2: pmcsas_asyncd_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'device_count: expected 96 (96), registered 96'}

[?]  Sun Dec 10 01:29:26 +0900 [node2: pmcsas_timeout_0: sas.adapter.debug:info]: params: {'adapterName': '0a', 'debug_string': 'Stop kicking open SDM batch window.'}