Applies to Data ONTAP 7 and earlier ONTAP 9 Issue Output of df -A and df shows the difference between the amount of space used on the aggregate and the actual size of the volume in the kbytes column o...Applies to Data ONTAP 7 and earlier ONTAP 9 Issue Output of df -A and df shows the difference between the amount of space used on the aggregate and the actual size of the volume in the kbytes column of the df command
Data ONTAP 7.1 or later contains FlexVol volume auto-grow and free space preservation features that allows the FlexVol volume to grow automatically based on storage needs and reduces the chance of the...Data ONTAP 7.1 or later contains FlexVol volume auto-grow and free space preservation features that allows the FlexVol volume to grow automatically based on storage needs and reduces the chance of the volume running out of space.
With this value set to on, Data ONTAP ignores any filesystem inconsistencies that exist, or that might arise. If set to on, contact NetApp Technical Support to address the issue. To check via CLI run ...With this value set to on, Data ONTAP ignores any filesystem inconsistencies that exist, or that might arise. If set to on, contact NetApp Technical Support to address the issue. To check via CLI run the following: ::>storage aggregate show -aggregate <aggr> filer::> storage aggregate show -aggregate aggr0 Disks for First Plex: 1.21.0, 1.21.1, 1.21.3 Disks for Mirrored Plex: - Ignore Inconsistent: on For Data ONTAP running in 7mode run the aggr status command to check the status.
The NFS clients that held locks on the affected storage system must be notified via the Network Status Monitor (NSM) as detailed in the sections above. Because of the upper limit of 5 minutes on the s...The NFS clients that held locks on the affected storage system must be notified via the Network Status Monitor (NSM) as detailed in the sections above. Because of the upper limit of 5 minutes on the startup of each service on a cluster failover/takeover, the delay in contacting the NLM clients could further compound the startup of the failed filer and could impact the overall availability of the cluster
RLM heartbeat stopped Cluster Notifications continue to be sent from an RLM card which is not connected, generating alerts to the user (RLM HBT STOPPED) CRITICAL and generation of related autosupport ...RLM heartbeat stopped Cluster Notifications continue to be sent from an RLM card which is not connected, generating alerts to the user (RLM HBT STOPPED) CRITICAL and generation of related autosupport emails. The RLM generating the error messages is not connected to the network. Issuing the command rlm reboot does not stop the messages from being generated because it does not reset the configuration of the RLM.
For the performance reason, you may need to increase the "cifs.max_mpx" to 1124 while using the storage system with a Windows Terminal Server (WTS). "...This hotfix raises the upper limit for the MaxC...For the performance reason, you may need to increase the "cifs.max_mpx" to 1124 while using the storage system with a Windows Terminal Server (WTS). "...This hotfix raises the upper limit for the MaxCmds parameter to 65,535, and the upper limit for the MaxMpxCt parameter to 65,535. If the Windows 2000-based server detects a client that is running Windows 95 or Windows 98, it behaves as if the MaxMpxCt value is no larger than 125.
Applies to Data ONTAP 7 and earlier Description Downloading disk firmware when upgrading Data ONTAP. Manually downloading disk firmware prior to reboot on the new platform. Panic caused by attempting ...Applies to Data ONTAP 7 and earlier Description Downloading disk firmware when upgrading Data ONTAP. Manually downloading disk firmware prior to reboot on the new platform. Panic caused by attempting to download disk firmware with clustering disabled. Updating firmware and Data ONTAP.
Applies to Data ONTAP 7 and earlier Description This article describes the procedure that should be followed to set Additional User Rights Assignments on a NetApp storage system using Active Directory
Applies to Data ONTAP 7 and earlier Issue Applications that create new files on volumes that have quotas applied might lead to scenarios where empty files of 0 Kb are left behind.
