Applies to ONTAP 9.8P12 SnapMirror Issue After ONTAP upgrade a few SnapMirror relationship fail to create snapshots on the source: status=Failure message=Failed to create Snapshot copy snapmirror.12ab...Applies to ONTAP 9.8P12 SnapMirror Issue After ONTAP upgrade a few SnapMirror relationship fail to create snapshots on the source: status=Failure message=Failed to create Snapshot copy snapmirror.12abc123-1234-12ab-1234-1234567890_abc1234567.2022-12-31_144000 on volume svm_src:vol_src.(CSM: Connection refused.)
This is the resolution guide for the ONTAP EMS message csm.mismatchRemoteDevice. The article provides the EMS Identifier and Syslog Translator. As per the cause of the ONTAP EMS message, the Solution...This is the resolution guide for the ONTAP EMS message csm.mismatchRemoteDevice. The article provides the EMS Identifier and Syslog Translator. As per the cause of the ONTAP EMS message, the Solution KBs have been provided.
Applies to OnTap 9.5 Issue Scheduled snapmirror updates for a relationship are failing. Manual updates at a different time of day are successful. Snapmirror update error message: Failed to create Snap...Applies to OnTap 9.5 Issue Scheduled snapmirror updates for a relationship are failing. Manual updates at a different time of day are successful. Snapmirror update error message: Failed to create Snapshot copy ***** on volume *****. (CSM: Try again.)
ONTAP uses Cluster Session Manager (CSM) communication channels to exchange information between nodes in a cluster. The following issues are seen: CSM session failures that result from application tri...ONTAP uses Cluster Session Manager (CSM) communication channels to exchange information between nodes in a cluster. The following issues are seen: CSM session failures that result from application triggers or long idle sessions pose no risk to the system. In contrast, connection-related failures should be investigated, and may represent a larger whole issue. As all three scenarios are presented as csm.sessionFailed:warnings, we must investigate to determine the root cause of the warning.
Failed to get information for source volume 'XXXX' for confirmation.(CSM: Connection aborted.) Failed to get information for source volume "vserver1:Source_vol" for setup of transfer.(CSM: Non-specifi...Failed to get information for source volume 'XXXX' for confirmation.(CSM: Connection aborted.) Failed to get information for source volume "vserver1:Source_vol" for setup of transfer.(CSM: Non-specific invalid argument.) Transfer failed.(CSM: Connection refused.) Transfer failed.(Replication operation request failed from Cluster Id: <id#>, Node Id: <id#> to Cluster Id: <id#>, Node Id: <id#> due to a network error(CSM: Operation referred to a non-existent session.))
Cluster peering is stuck in pending with CSM error CSM_CONN_TEMP_AUTH_CHANGE. Peer Cluster Name Cluster Serial Number Availability Authentication [?] Mon Jul 19 11:27:12 +0200 [cluster_node_name: CsmM...Cluster peering is stuck in pending with CSM error CSM_CONN_TEMP_AUTH_CHANGE. Peer Cluster Name Cluster Serial Number Availability Authentication [?] Mon Jul 19 11:27:12 +0200 [cluster_node_name: CsmMpAgentThread: csm.sessionFailed:debug]: Cluster interconnect session (req=cluster_node_name:dblade, rsp=cluster_node_name:dblade, uniquifier=0705c197627b642f) failed with record state ACTIVE, CSM error CSM_CONN_TEMP_AUTH_CHANGE, low-level error UNKNOWN, socket error 0, and TLS error 0.
The source is currently connected to switch(SN) remote device and the destination is currently connected to switch(SN) remote device. Wed Mar 24 23:26:02 MDT [node-name: vifmgr: vifmgr.clntdev.updated...The source is currently connected to switch(SN) remote device and the destination is currently connected to switch(SN) remote device. Wed Mar 24 23:26:02 MDT [node-name: vifmgr: vifmgr.clntdev.updated:notice]: Remote device switch(SN) (model: NX3132V, version: Cisco Nexus Operating System (NX-OS) Software, Version 7.0(3)I7(8), IP address: 10.109.32.157) has been detected on the cluster network.
If the message repeats every few minutes, it might indicate a problem in the cluster interface configuration or the physical cabling of the switchless cluster Additional issues on the cluster may aris...If the message repeats every few minutes, it might indicate a problem in the cluster interface configuration or the physical cabling of the switchless cluster Additional issues on the cluster may arise due to the cross-cabled ports, and thus identifying and resolving the cross-cabled ports is the first step prior to resolving any other issues on your cluster
