Skip to main content
NetApp Knowledge Base

Fail to create MetroCluster  interface with error messages "operation timeout"

Views:
122
Visibility:
Public
Votes:
0
Category:
metrocluster
Specialty:
metrocluster
Last Updated:

Applies to

  • MetroCluster IP
  • ONTAP 9

Issue

  • When configuring a new MetroCluster, it fails to create the MetroCluster IP interfaces with the below error messages:

MCCIP01::> metrocluster configuration-settings interface create -cluster-name MCCIP01 -home-node MCCIP01-01 -home-port e0a -address 192.168.100.120 -netmask 255.255.255.0 -vlan-id 220

Warning: Verify that the attached switches' RCF has been updated with the VLAN ID
value specified using "-vlan-id" parameter before proceeding further.
Do you want to continue? {y|n}: y

[Job 274] Job is queued: Metrocluster Interface Create Job.
[Job 274] Creating interface.
[Job 274] Retrying the operation.
[Job 274] Creating interface.
[Job 274] Retrying the operation.
[Job 274] Creating interface.
[Job 274] Retrying the operation.
[Job 274] Creating interface.
[Job 274] Retrying the operation.
[Job 274] Creating interface.
[Job 274] Retrying the operation.
[Job 274] Verifying if the partner cluster is reachable.
[Job 274] Creating interface.
[Job 274] Job failed: Failed to create an interface for port "e0a-220" node
"MCCIP01-01" in cluster "MCCIP01". Reason: Timeout: Operation
"kern_metrocluster_interface_setup_iterator::create_imp()" took longer than 25
seconds to complete [from mgwd on node "MCCIP01-02" (VSID: -3) to kernel at
169.254.250.207] Use the "metrocluster operation show" command to view detailed
error information. Resolve the errors, then try the command again.

MCCIP01::> metrocluster operation show
Operation: interface-create
State: failed
Start Time: 9/20/2022 16:08:41
End Time: 9/20/2022 16:12:07
Errors: Failed to create an interface for port "e0a-220" node "MCCIP01-01" in cluster "MCCIP01". Reason: Timeout: Operation "kern_metrocluster_interface_setup_iterator::create_imp()" took longer than 25 seconds to complete [from mgwd on node "MCCIP01-02" (VSID: -3) to kernel at 169.254.250.207]

 

  • The command "metrocluster interconnect adapter show" shows different IP address and VLAN-id:

MCCIP01::> metrocluster interconnect adapter show
Adapter Link
Node Adapter Name Type Status IP Address Port Number
------------ --------------- ------- ------ ----------- -----------
MCCIP01-01 e0a-10 iWARP UP 10.0.10.1 e0a-10
MCCIP01-01 e0b-20 iWARP UP 10.0.20.1 e0b-20
MCCIP01-02 e0a-10 iWARP UP 10.0.10.2 e0a-10
MCCIP01-02 e0b-20 iWARP UP 10.0.20.2 e0b-20
4 entries were displayed.

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.