Skip to main content
NetApp Knowledge Base

Search

  • Filter results by:
    • View attachments
    Searching in
    About 5 results
    • e0M port showing connected to partner e0M
      https://kb.netapp.com/on-prem/ontap/OHW/OHW-KBs/e0M_port_showing_connected_to_partner_e0M
      Applies to AFF systems FAS systems ONTAP 9 Cisco Discovery Protocol (CDP) Issue Network port show and device discovery report that the e0M port of a node is directly connected to the e0M port of the p...Applies to AFF systems FAS systems ONTAP 9 Cisco Discovery Protocol (CDP) Issue Network port show and device discovery report that the e0M port of a node is directly connected to the e0M port of the partner node
    • BES-53248 not automatically discovered with CDP/ISDP
      https://kb.netapp.com/on-prem/Switches/Broadcom-KBs/S_53248_cannot_be_monitored_with_CDP_ISDP
      Applies to BES-53248 cluster network switches. Cisco Discovery Protocol (CDP) Simple Network Management Protocol (SNMP) Cluster Switch Health Monitor (CSHM) Issue CN1610 replaced with BES-53248 not au...Applies to BES-53248 cluster network switches. Cisco Discovery Protocol (CDP) Simple Network Management Protocol (SNMP) Cluster Switch Health Monitor (CSHM) Issue CN1610 replaced with BES-53248 not automatically discovered with CDP/ISDP
    • ONTAP Cluster setup aborted with "Unused cluster ports exist in the cluster"
      https://kb.netapp.com/on-prem/ontap/Ontap_OS/OS-KBs/ONTAP_Cluster_setup_aborted_with_Unused_cluster_ports_exist_in_the_cluster
      Applies to ONTAP 9 New cluster setup Issue Cluster Setup following the selection of cluster ports fails with the following error. Error:Unused cluster ports exist in the cluster One or more ports may ...Applies to ONTAP 9 New cluster setup Issue Cluster Setup following the selection of cluster ports fails with the following error. Error:Unused cluster ports exist in the cluster One or more ports may not be in the "healthy" state, or may be incorrectly assigned to the "Cluster" Ipspace. Run "network port show -ipspace Cluster" to view the cluster ports. Correct any issue, and then try the command again.
    • Why is "cdp enable" not showing in running-config on cisco switches after applying the RCF?
      https://kb.netapp.com/on-prem/ontap/mc/MC-KBs/Why_is_cdp_enable_not_showing_in_running_config_on_cisco_switches_after_applying_the_RCF
      Cisco Discovery Protocol (CDP) The cdp enable setting is only visible in the running-config if it is globally disabled To verify the CDP setting use the show cdp neighbors command instead site-a-sw2# ...Cisco Discovery Protocol (CDP) The cdp enable setting is only visible in the running-config if it is globally disabled To verify the CDP setting use the show cdp neighbors command instead site-a-sw2# show cdp neighbors Capability Codes: R - Router, T - Trans-Bridge, B - Source-Route-Bridge S - Switch, H - Host, I - IGMP, r - Repeater, cbc-mgmt-sw-r01 mgmt0 138 S I WS-C2960-24TT Fas0/22 For the diffrent version of nexus os use the cisco web site for more documentation on the commands
    • Cannot see one of the two cluster switch from "cluster-switch show" command output
      https://kb.netapp.com/on-prem/ontap/OHW/OHW-KBs/Cannot_see_one_of_the_two_cluster_switch_from_cluster_switch_show_command_output
      Cluster Switch Health Monitor (CSHM) Both cluster switch are working normal, but cannot see one from cluster-switch show command output. From the system cluster-switch show command just can see only o...Cluster Switch Health Monitor (CSHM) Both cluster switch are working normal, but cannot see one from cluster-switch show command output. From the system cluster-switch show command just can see only one switch info Cluster::> system cluster-switch show -instance Software Version: Cisco Nexus Operating System (NX-OS) Software, Version 7.1(1)N1(1) From the cdpd show-neighbors can see both switch info. Version: Cisco Nexus Operating System (NX-OS) Software, Version 7.1(1)N1(1)