Skip to main content
NetApp Knowledge Base

Just one node reports increased temperature and the failure of both power supplies

Views:
508
Visibility:
Public
Votes:
0
Category:
aff-series
Specialty:
hw
Last Updated:

Applies to

AFF A250

Issue

  • Just one AFF A250 node reports high chassis temperature and two power supplies failures. Example:

::>event log show -event monitor*,chassis*
Severity  Event
--------- ----------------------------------------------
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 In Fault is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 Fan is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 FB Hot is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 Hot is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 Inlet is Unreadable
ERROR     callhome.chassis.hitemp: Call home for CHASSIS OVER TEMPERATURE
EMERGENCY monitor.globalStatus.critical: Power Supply Status Critical: PSU2, PSU1. Chassis temperature is too high..
ERROR     monitor.temp.unreadable: The controller temperature (PSU2 FB Hot) is not readable.
ERROR     monitor.temp.unreadable: The controller temperature (PSU2 Hot) is not readable.
ERROR     monitor.temp.unreadable: The controller temperature (PSU2 Inlet) is not readable.
ERROR     monitor.temp.unreadable: The controller temperature (PSU1 FB Hot) is not readable.
ERROR     monitor.temp.unreadable: The controller temperature (PSU1 Hot) is not readable.
ERROR     monitor.temp.unreadable: The controller temperature (PSU1 Inlet) is not readable.
ERROR     callhome.chassis.ps.degraded: Call home for CHASSIS POWER SUPPLY DEGRADED: PS 1
EMERGENCY monitor.globalStatus.critical: Power Supply Status Critical: PSU2, PSU1.
ERROR     callhome.chassis.power: Call home for CHASSIS POWER DEGRADED: Power Supply Status Critical: PSU2, PSU1.
ALERT     monitor.chassisPower.degraded: Chassis power is degraded: Power Supply Status Critical: PSU2,PSU1.
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 2 is degraded: PSU2 Hot is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 2 is degraded: PSU2 Inlet is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 Out Fault is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 Warning is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 In Fault is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 Fan is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 FB Hot is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 Hot is Unreadable
NOTICE    monitor.chassisPowerSupply.degraded: Chassis power supply 1 is degraded: PSU1 Inlet is Unreadable

  • All sensors are ok in the partner node:

::> system controller environment show
Node               FRU Name                       State
------------------ ------------------------------ -----------
netappv17-01       PSU2                           GOOD
netappv17-01       PSU1                           GOOD
netappv17-02       PSU2                           unknown
netappv17-02       PSU1                           unknown

  • One embedded NSM8E module reports:
[dsa_worker3: ses.status.enclWarn:error]: NS224NSM8E (S/N SHJHU0123456789) shelf 0 on channel 0s disk enclosure warning for Enclosure 1: VPD EEPROMs mismatch or unreadable. This element is on the unknown location.
[dsa_worker3: ses.status.ModuleWarn:alert]: NS224NSM8E (S/N SHJHU0123456789) shelf 0 on channel 0s PCI switch warning for PCI Switch 2: non-critical status; Backplane VPD SEEROM corrupt or unreadable. This element is on the rear of the shelf at the bottom, on shelf module (B).
  • storage show fault output:
Enclosure Status: non-critical
Channel: 0s
Shelf: 0
Shelf Type: NS224NSM8E
Module Type: NSM8E
Enclosure:
Element Status Status Bytes Status Descriptions
1: NONCRITICAL 03,00,00,00
PSM:
Element Status Status Bytes Status Descriptions
1 [NSM8E A] : NONCRITICAL 03,0C,00,00 MIDPLANE VPD FAULT, MASTER
2 [NSM8E B] : NONCRITICAL 03,04,00,00 MIDPLANE VPD FAULT
  • Issue remains after PSUs and node re-seat.
  • Issue remains with a known working PSU.
  • Issue follows one chassis slot, when swapping controllers between them.

Sign in to view the entire content of this KB article.

New to NetApp?

Learn more about our award-winning Support

NetApp provides no representations or warranties regarding the accuracy or reliability or serviceability of any information or recommendations provided in this publication or with respect to any results that may be obtained by the use of the information or observance of any recommendations provided herein. The information in this document is distributed AS IS and the use of this information or the implementation of any recommendations or techniques herein is a customer's responsibility and depends on the customer's ability to evaluate and integrate them into the customer's operational environment. This document and the information contained herein may be used solely in connection with the NetApp products discussed in this document.